Citizen Promaster D203 Manual Arts

Posted on by
Citizen Promaster D203 Manual Arts Rating: 7,4/10 9784reviews

I have one of these watches and the case needs a good cleaning. I have removed the movement and I'm thinking that before using any water or any other substance on it I should remove the sensor, right? If yes, how do I do it?

The Citizen Promaster Cyber Aqualand Nx (MG1000-01E) watch is one of the best watches launched by Citizen. It belongs to the Citizen Cyber Aqualand.

Do you just push it out from within? If not, do I just clean it carefully without touching that plastic wire/contact/connector thing that goes connected to the movement? Also, could someone tell me what the part number for the glass is? Or at least what are the dimensions? Full model name is citizen c500-e80338 ta. While on the subject, how are the pushers removed? I'd like to clean them and lubricate them as well.

Aloha Kintako.no need to remove that Sensor. Stated that can be FRAGILE and DAMAGE'D also. This is what they look like when removed and the problem might be they have to be. ' Pressed Back into the case '. If damaged I made a.

Citizen Promaster Watch Manual

Jig to press others in again but don't remove it. I never remove them unless damaged, just wash the case good and be careful not to damage the.

' Shield Cover Guard '. To blow sediment or excess Soap or Crud in it out. Picture - 1 That Guard in pressed in and the edges are Crimped to hold it but it can be removed if needed but don't damage the edges of it.

Picture - 3 Guard / Seal Ring / Nylon Gasket. ( Note: - All Three very hard to get as parts. ) No Sensor shown. ( SAMPLE: This is my C506 and same setup also. ) Still needs a movement yet. Aloha Kintako, Yes don't remove it at all just clean it up.

I just wash it with regular. Dawn Dish Soap. Because it works good. I usually.Soak and Wash. Most of my Cases in. DAWN DISH SOAP. It gets everything clean.

But.Remember don't soak that Minute Track Ring at all. The C023 models and most I use.DAWN SOAP. Also for them and never had a bad result with it yet.

The Tail for the. SENSOR it is sealed already but don't rub it hard because the sealant might chip or crack. Use a nice Art brush and Tooth Brush it will be just fine. Louis NOTE: lewie might be able to help you with that Crystal measurements I don't have that one noted here.

Aloha, Kintako, They some times fade or loose their markings. If they get liquid on them and you touch them some are stick on Clear Decals. They come on plastic Materials or Metal on many. I usually just touch them very little with a Q-Tip with no cleaner at all. Unless they are.Engraved, I would not trust hard cleaning or Rubbing at all.

Louis NOTE: If at all possible. DO NOT REMOVE THE BEZEL, because you are going to struggle on it later if not knowing how to do it. These ae very tight fitted and if you bend or warp it, it will be a goner. Clean with good cleaner and just rotate it so the Dirt comes out. Use Air Can or Compressor if you have it. Aloha Kintako.

Just a point. When you strip these Digital Watch's and you get those readings that is because you may have touched the Screen to hard while you handled it. This is what happens when you do that. Some times this is caused when you miss align the movement Bodies when you re-assemble them also.

This picture is a example of this: Pic. It also can happen if you press it to much to assemble it. Also if you wiped it and did it to hard. These are very fragile to handle of work on if not careful. NOTE: Remember just a Points given alright.?? As.lewie has stated why are you stripping it down so far to get it fixed. These are only done to the actual fix if still working that you get it to see what is going on with the.

PCB Board if It is not working. To service the whole watch and then it does not work again it should have been left alone with the. PCB Screen and that Section. One can do the Movement gearing with out stripping. The Front Section of the watch and still be successful.

These Digital Screen Lens are made in.Two Parts. They have a very thin layer of some kind of Film made to be between the to plastic pieces from the Factory. To do any thing to them or mis-handled it would make the. Screen Window Malfunction to display the readings for it.

Picture - 4: This is the movement complete to place the old one. These are very crucial when split, and the Digital section does not work. If the reading for the Digital has gone bad it is most likely because the contact are on the. PCB BOARD has.

Defects or Dirty or has been damaged. It could be also that the contact area has still to be placed on the surface better. Tx Sr607 Firmware Update.

Slice 1 Arrow pointing down Arrow pointing left Arrow pointing right Shopping Cart An image of a small shopping cart to put the items that you've selected into. Clock Icon An image of a clock. Close Icon A graphic of an X to signify a call to action to close a pop-up.

Minus The Bear Acoustics 2 Zip. Email Icon An image of an envelope to represent email. Expand Icon A graphic of an outlined cirle with a + at the center that represents a call to action to expand a certain element. Facebook Icon An image of a lowercase f that represents the Facebook logo. Instagram Icon An image that looks similar to a small poloroid camera that represents the Instagram logo. Location Pin Icon An image of a marker to represent a point on a map or a location.

Citizen Logo Slice 1 Title Movement Telephone Icon An image of a telephone. Pinterest Icon A graphic of a circle with a P in the center to represent the Pinterest logo. Search Icon An image of a small magnifying to signify search. Full-Filled In Star Icon Half-Filled Star Icon Twitter Icon A silhouette of a small bird that represents the Twitter logo. YouTube Icon This is an image of the YouTube logo. This image contains a box with rounded corners with a centered triangle pointing right. This graphic is suppose to represent a play button on top of a video.